Ventura Alloy And Steels Private Limited

We are manufacturer and supplier of DB6 Steel Die Block .

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

Eaf+Lf+Vd+Upset+Forged+Annealed+Rough Turned For Rounds/Milled For Flats+Oil Quenched And Double Tempered+ Rough Turned For Rounds/Milled For Flats

Steel Properties:
The special Hot Work Pre-hardened Steel has great toughness and high wear resistance. DB6 Steel is generally supplied in hard, quenched, tempered and also in annealed condition in special cases. Usually it's working hardness is 360-430 BHN. This steel grade is the upgraded version of DIN 2713 for greater efficiency and performance.

Application:
Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Cassettes, Piston Rods, Cranks, Boaster, Shearing Blades, Tools, Plastic Moulds etc.

We are offering 1.2714 Stainless Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

EAF+LF+VD+UPSET+FORGED+ANNEALED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS+OIL QUENCHED AND DOUBLE TEMPERED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS

Steel Properties:

The exceptional Hot Work Pre-solidified Steel has great toughness and high wear resistance. DB6 Steel is generally provided in hard, quenched, tempered and annealed condition in strengthened condition in exceptional cases. Normally it's working hardness is 360-430 BHN. This steel grade is the updated type of DIN 2713 for higher efficiency and performance.

Application:

Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Piston Rods, Bolster, Cranks, Cassettes, Plastic Moulds, Shearing Blades, Tools etc.

As rolled and Spheroidized Annealed

EN24 steel is a medium carbon, low alloy steel known for its toughness and strength in generally large sections. EN24 is likewise one kind of nickel chromium molybdenum steels. It can be supplied hardened and tempered in the tensile range of 930-1080 Mpa as well as annealed condition. Pre hardened and tempered EN24 steels can be further surface hardened by flame or induction hardening and by nitriding. EN24 steel is high tensile alloy steel famous for its excellent wear resistance properties and in addition to where high strength properties are required. This Grade is used in components affiliated to shafts, gears, studs and bolts. Its hardness is within the range of 248~302 HB.

Steel Properties:

• Standard high-speed steel grade
• Contains well-balanced alloy composition
• High toughness
• Great cutting edge retention

Physical Properties:

Heat Treatment:

We are offering 1.2714 Die Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

Eaf+Lf+Vd+Upset+Forged+Annealed+Rough Turned For Rounds/Milled For Flats+Oil Quenched And Double Tempered+ Rough Turned For Rounds/Milled For Flats

Steel Properties:
The special Hot Work Pre-hardened Steel has great toughness and high wear resistance. DB6 Steel is generally supplied in hard, quenched, tempered and also in annealed condition in special cases. Usually it's working hardness is 360-430 BHN. This steel grade is the upgraded version of DIN 2713 for greater efficiency and performance.

Application:
Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Cassettes, Piston Rods, Cranks, Boaster, Shearing Blades, Tools, Plastic Moulds etc.

We are offering 56NICRMOV7 Hot Work Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

Eaf+Lf+Vd+Upset+Forged+Annealed+Rough Turned For Rounds/Milled For Flats+Oil Quenched And Double Tempered+ Rough Turned For Rounds/Milled For Flats

Steel Properties:
The special Hot Work Pre-hardened Steel has great toughness and high wear resistance. DB6 Steel is generally supplied in hard, quenched, tempered and also in annealed condition in special cases. Usually it's working hardness is 360-430 BHN. This steel grade is the upgraded version of DIN 2713 for greater efficiency and performance.

Application:
Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Cassettes, Piston Rods, Cranks, Boaster, Shearing Blades, Tools, Plastic Moulds etc.

We are offering 55NICRMOV7 Hot Work Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

Eaf+Lf+Vd+Upset+Forged+Annealed+Rough Turned For Rounds/Milled For Flats+Oil Quenched And Double Tempered+ Rough Turned For Rounds/Milled For Flats

Steel Properties:
The special Hot Work Pre-hardened Steel has great toughness and high wear resistance. DB6 Steel is generally supplied in hard, quenched, tempered and also in annealed condition in special cases. Usually it's working hardness is 360-430 BHN. This steel grade is the upgraded version of DIN 2713 for greater efficiency and performance.

Application:
Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Cassettes, Piston Rods, Cranks, Boaster, Shearing Blades, Tools, Plastic Moulds etc.

We are offering H13 Hot Work Stainless Steel Blockto our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels supplies and stocks H13 tool steel in flat, square and round bar. We provide steel in all sizes as your requirements. Consult our team who will assist you for any query related to H13 steel.

SAE AISI H13 steel equivalent with JIS SKD61, GB 4Cr5MoSiV1 and DIN 1.2344 Tool Steel. AISI H13 steel consists of chromium, molybdenum and vanadium and is known for its high hardenability and great toughness.

It also combines shock and abrasion resistance, has good red hardness, can resist rapid cooling and withstand premature heat checking.

H13 Tool Steel has high hot-wear resistance abilities along with great strength, heat conductivity and invulnerability to hot cracking. It has good resistance to abrasion at each low and high temperature. It displays high level of toughness and ductility. H13 has Uniform and high level of machinability and polish ability. It has high-temperature strength and resistance to thermal fatigue, glorious through-hardening properties and shows very limited distortion during hardening.

H3 ESR is the most purified material with the conventional VD route. The nature of material increase the strength, exceptionally increase the micro-cleanness level. H13 ESR is most refined, has greater homogeneity and an exceptionally fine structure, resulting in improved machinability, polishing & high-temperature tensile strength. H13 is completely ultrasonic examined with 100% positive outcomes according to NDT standards.

Steel Properties:

• Great toughness
• Thermal conductivity
• High hot-wear resistance
• Hot tensile strength
• Insusceptible for hot cracking (Hot Crack resistant)
• Can be water-cooled to a restricted degree
• High Hardenability

Application:

This steel is especially used for ejector pins, tool holders and shrink work chucks. It is majorly widely utilized for manufacture of hot forging die & inserts, hot gripper dies, hot nut tools, hot header dies, brass forging and pressing dies, hot forging aluminum base dies, aluminum casting and extrusion dies, zinc die casting dies, extrusion mandrels, cores, die holder blocks, hot press dies, hot work punches, etc.

We are manufacturer and supplier Of DB6 Tool Steel.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

Eaf+Lf+Vd+Upset+Forged+Annealed+Rough Turned For Rounds/Milled For Flats+Oil Quenched And Double Tempered+ Rough Turned For Rounds/Milled For Flats

Steel Properties:
The special Hot Work Pre-hardened Steel has great toughness and high wear resistance. DB6 Steel is generally supplied in hard, quenched, tempered and also in annealed condition in special cases. Usually it''s working hardness is 360-430 BHN. This steel grade is the upgraded version of DIN 2713 for greater efficiency and performance.

Application:
Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Cassettes, Piston Rods, Cranks, Boaster, Shearing Blades, Tools, Plastic Moulds etc.

Size Range:
ROUNDS - 60 to 1000 MM DIA

BLOCKS - Thickness - 125 to 1000 MM MAX | Width - 130 to 1600 MM MAX

PRICE RANGEL:
ROUNDS -Rs.145 to 170 per Kg
BLOCKS - Rs.155 to 195 per Kg

Stocking Partners:
We keep the materials from Germany, Japan and China.

For PHYSICAL PROPERTIES & HEAT TREATMENT, refer our website http://www.venturasteels.com/

Chemical Composition - (Typical Analysis in %)

H21 Steel is a hot work tool steel for oil or air hardening to develop high hot quality, support of hardness, and warmth checking resistance.

This is mostly utilized as hot work devices, instruments for manufacture of hollows, screws, rivets, nuts and bolts. Die casting tools, forming dies, die inserts, hot shear blades.

Steel Properties:

Hot work steel has great toughness and contains Tungsten, Chromium, Carbon, Vanadium and generally its working hardness is 40.0 to 55.0 HRC size and is accessible in round, level and square shapes.

Application:

The H21 tungsten hot-work tool steels are primarily utilized for hot-working dies and tooling. For example extrusion, die casting & hot-forming of parts.

Physical Properties:

We are offering 1.2714 Hot Work Stainless Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

EAF+LF+VD+UPSET+FORGED+ANNEALED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS+OIL QUENCHED AND DOUBLE TEMPERED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS

Steel Properties:

The exceptional Hot Work Pre-solidified Steel has great toughness and high wear resistance. DB6 Steel is generally provided in hard, quenched, tempered and annealed condition in strengthened condition in exceptional cases. Normally it's working hardness is 360-430 BHN. This steel grade is the updated type of DIN 2713 for higher efficiency and performance.

Application:

Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Piston Rods, Bolster, Cranks, Cassettes, Plastic Moulds, Shearing Blades, Tools etc.

• D3 Steel
• High Carbon - 2%
• High Chromium - 12%

We are offering 55NICRMOV7 Die Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

Eaf+Lf+Vd+Upset+Forged+Annealed+Rough Turned For Rounds/Milled For Flats+Oil Quenched And Double Tempered+ Rough Turned For Rounds/Milled For Flats

Steel Properties:
The special Hot Work Pre-hardened Steel has great toughness and high wear resistance. DB6 Steel is generally supplied in hard, quenched, tempered and also in annealed condition in special cases. Usually it's working hardness is 360-430 BHN. This steel grade is the upgraded version of DIN 2713 for greater efficiency and performance.

Application:
Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Cassettes, Piston Rods, Cranks, Boaster, Shearing Blades, Tools, Plastic Moulds etc.

We are offering 2343 Hot Work Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Supplies and Stocks AISI H11 tool steel is a 5% chromium hot work tool steel that is represented by its excellent impact toughness. Chromium hot-work tool steels are designated as group H steels according to the AISI classification system, and specified in ASTM A681 standard. The most commonly used chromium hot-work steels are H11 tool steel, H12 tool steel, and H13 steel, within the series from H1 to H19.

If we compare between H11 and H13, H11 tool steel consists of less vanadium than the commonly used H13 hot work tool steel. That gives minimal size change during heat treatment. H11 how work steel also has super resistance to thermal fatigue cracking and superb resistance to gross cracking and thermal shock when water cooled in service.

H11 steel is inclusive of all hot work tool steel with excellent rigidity and durability along with great thermal conductivity and invulnerability to hot cracking and can be water cooled to a constrained degree. H11 is primarily used for apparatus holders , ejector pins and shrink fit chucks.

Steel Properties:

• Contains 5% Chromium
• Greater strength
• High toughness
• Best thermal physical phenomenon
• Resistant to hot cracking
• Gives fundamental necessities to long tool life in press forging, die-casting, extrusion processes etc.

Application:

This grade isn't utilized for typical applications in the area of hot-work steels, yet additionally useful for tool holders, bridge kind tools, ejector pins, liner holders, hot work punches, forging dies, and shrink work chucks.

We are offering 1.2344 Hot Work Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels supplies and stocks H13 tool steel in flat, square and round bar. We provide steel in all sizes as your requirements. Consult our team who will assist you for any query related to H13 steel.

SAE AISI H13 steel equivalent with JIS SKD61, GB 4Cr5MoSiV1 and DIN 1.2344 Tool Steel. AISI H13 steel consists of chromium, molybdenum and vanadium and is known for its high hardenability and great toughness.

The molybdenum and vanadium act as strengthening agents while the chromium content helps the AISI H-13 tool steel to withstand softening when used at high temperatures.

H13 Tool Steel has high hot-wear resistance abilities along with great strength, heat conductivity and invulnerability to hot cracking. It has high-temperature strength and resistance to thermal fatigue, glorious through-hardening properties and shows very limited distortion during hardening.

H3 ESR is the most purified material with the conventional VD route. The nature of material increase the strength, exceptionally increase the micro-cleanness level. H13 ESR is most refined, has greater homogeneity and an exceptionally fine structure, resulting in improved machinability, polishing & high temperaturetensile strength. Exceptionally suggest the use of AISI-H13 ESR grade for Aluminum Pressure Die Casting and other part subjected to high working temperatures and high weight quality. H13 is completely ultrasonic examined with 100% positive outcomes according to NDT standards.

Steel Properties:

• Great toughness
• Thermal conductivity
• High hot-wear resistance
• Hot tensile strength
• Insusceptible for hot cracking (Hot Crack resistant)
• Can be water-cooled to a restricted degree
• High Hardenability

Application:

This steel is especially used for ejector pins, tool holders and shrink work chucks. It is majorly widely utilized for manufacture of hot forging die & inserts, hot gripper dies, hot nut tools, hot header dies, brass forging and pressing dies, hot forging aluminum base dies, aluminum casting and extrusion dies, zinc die casting dies, extrusion mandrels, cores, die holder blocks, hot press dies, hot work punches, etc.

We are offering 2343 Hot Die Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Supplies and Stocks AISI H11 tool steel is a 5% chromium hot work tool steel that is represented by its excellent impact toughness. Chromium hot-work tool steels are designated as group H steels according to the AISI classification system, and specified in ASTM A681 standard. The most commonly used chromium hot-work steels are H11 tool steel, H12 tool steel, and H13 steel, within the series from H1 to H19.

If we compare between H11 and H13, H11 tool steel consists of less vanadium than the commonly used H13 hot work tool steel. This gives H11 steels the higher toughness, with some reduction in wear resistance and tamper resistance. That gives minimal size change during heat treatment. H11 how work steel also has super resistance to thermal fatigue cracking and superb resistance to gross cracking and thermal shock when water cooled in service.

H11 steel is inclusive of all hot work tool steel with excellent rigidity and durability along with great thermal conductivity and invulnerability to hot cracking and can be water cooled to a constrained degree. H11 is primarily used for apparatus holders ,ejector pins and shrink fit chucks.

Steel Properties:

• Contains 5% Chromium
• Greater strength
• High toughness
• Best thermal physical phenomenon
• Resistant to hot cracking
• Gives fundamental necessities to long tool life in press forging, die-casting, extrusion proceses etc.

Application:

This grade isn't utilized for typical applications in the area of hot-work steels, yet additionally useful for tool holders, bridge kind tools, ejector pins, liner holders, hot work punches, forging dies, and shrink work chucks.

We are offering 2714 Hot Work Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

EAF+LF+VD+UPSET+FORGED+ANNEALED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS+OIL QUENCHED AND DOUBLE TEMPERED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS

Steel Properties:

The exceptional Hot Work Pre-solidified Steel has great toughness and high wear resistance. DB6 Steel is generally provided in hard, quenched, tempered and annealed condition in strengthened condition in exceptional cases. Normally it's working hardness is 360-430 BHN. This steel grade is the updated type of DIN 2713 for higher efficiency and performance.

Application:

Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Piston Rods, Bolster, Cranks, Cassettes, Plastic Moulds, Shearing Blades, Tools etc.

Ventura Alloy and Steels Stocks and Supplies 55NCDVV7 Hot Work Steel Block in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

Eaf+Lf+Vd+Upset+Forged+Annealed+Rough Turned For Rounds/Milled For Flats+Oil Quenched And Double Tempered+ Rough Turned For Rounds/Milled For Flats

Steel Properties:
The special Hot Work Pre-hardened Steel has great toughness and high wear resistance. DB6 Steel is generally supplied in hard, quenched, tempered and also in annealed condition in special cases. Usually it's working hardness is 360-430 BHN. This steel grade is the upgraded version of DIN 2713 for greater efficiency and performance.

Application:
Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Cassettes, Piston Rods, Cranks, Boaster, Shearing Blades, Tools, Plastic Moulds etc.

We are offering 1.2344 Die Stainless Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels supplies and stocks H13 tool steel in flat, square and round bar. We provide steel in all sizes as your requirements. Consult our team who will assist you for any query related to H13 steel.

SAE AISI H13 steel equivalent with JIS SKD61, GB 4Cr5MoSiV1 and DIN 1.2344 Tool Steel. AISI H13 steel consists of chromium, molybdenum and vanadium and is known for its high hardenability and great toughness.

The molybdenum and vanadium act as strengthening agents while the chromium content helps the AISI H-13 tool steel to withstand softening when used at high temperatures. It also combines shock and abrasion resistance, has good red hardness, can resist rapid cooling and withstand premature heat checking.

H13 Tool Steel has high hot-wear resistance abilities along with great strength, heat conductivity and invulnerability to hot cracking. It has high-temperature strength and resistance to thermal fatigue, glorious through-hardening properties and shows very limited distortion during hardening.

H3 ESR is the most purified material with the conventional VD route. The nature of material increase the strength, exceptionally increase the micro-cleanness level. H13 ESR is most refined, has greater homogeneity and an exceptionally fine structure, resulting in improved machinability, polishing & high temperaturetensile strength. Exceptionally suggest the use of AISI-H13 ESR grade for Aluminum Pressure Die Casting and other part subjected to high working temperatures and high weight quality. H13 is completely ultrasonic examined with 100% positive outcomes according to NDT standards.

Steel Properties:

• Great toughness
• Thermal conductivity
• High hot-wear resistance
• Hot tensile strength
• Insusceptible for hot cracking (Hot Crack resistant)
• High Hardenability

Application:

This steel is especially used for ejector pins, tool holders and shrink work chucks. It is majorly widely utilized for manufacture of hot forging die & inserts, hot gripper dies, hot nut tools, hot header dies, brass forging and pressing dies, hot forging aluminum base dies, aluminum casting and extrusion dies, zinc die casting dies, extrusion mandrels, cores, die holder blocks, hot press dies, hot work punches, etc.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels supplies and stocks H13 tool steel in flat, square and round bar. We provide steel in all sizes as your requirements. Consult our team who will assist you for any query related to H13 steel.

SAE AISI H13 steel equivalent with JIS SKD61, GB 4Cr5MoSiV1 and DIN 1.2344 Tool Steel. AISI H13 steel consists of chromium, molybdenum and vanadium and is known for its high hardenability and great toughness.

The molybdenum and vanadium act as strengthening agents while the chromium content helps the AISI H-13 tool steel to withstand softening when used at high temperatures. It also combines shock and abrasion resistance, has good red hardness, can resist rapid cooling and withstand premature heat checking.

H13 Tool Steel has high hot-wear resistance abilities along with great strength, heat conductivity and invulnerability to hot cracking. It has good resistance to abrasion at each low and high temperature. It displays high level of toughness and ductility. H13 has Uniform and high level of machinability and polish ability. It has high-temperature strength and resistance to thermal fatigue, glorious through-hardening properties and shows very limited distortion during hardening.

H3 ESR is the most purified material with the conventional VD route. The nature of material increase the strength, exceptionally increase the micro-cleanness level. H13 ESR is most refined, has greater homogeneity and an exceptionally fine structure, resulting in improved machinability, polishing & high temperature tensile strength. Exceptionally suggest the use of AISI-H13 ESR grade for Aluminum Pressure Die Casting and other part subjected to high working temperatures and high weight quality. H13 is completely ultrasonic examined with 100% positive outcomes according to NDT standards.

Steel Properties:

• Great toughness

• Thermal conductivity

• High hot-wear resistance

• Hot tensile strength

• Insusceptible for hot cracking (Hot Crack resistant)

• Can be water-cooled to a restricted degree

• High Hardenability

Application:

This steel is especially used for ejector pins, tool holders and shrink work chucks. It is majorly widely utilized for manufacture of hot forging die & inserts, hot gripper dies, hot nut tools, hot header dies, brass forging and pressing dies, hot forging aluminum base dies, aluminum casting and extrusion dies, zinc die casting dies, extrusion mandrels, cores, die holder blocks, hot press dies, hot work punches, etc.

Steel Properties:

• High Carbon High Chromium contents.
• High wear resistant and toughness due to Vanadium addition of 0.90%.
• Supply condition is an Annealed which offer hardness to reach 57-59 HRC.
• Machinable in annealed condition.
• Better steel than D3 due to high alloy properties.

Application:

HCHCR D2 tool steel can be utilized for cold stamping or forming dies, cold forming rolls, slitters, shear blades, tools, tyre shredders, chipper knives, punches, trimming, cutting threading dies, stamping tools and more.

Physical Properties:

Heat Treatment:

We are offering 1.2714 Die Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

EAF+LF+VD+UPSET+FORGED+ANNEALED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS+OIL QUENCHED AND DOUBLE TEMPERED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS

Steel Properties:

The exceptional Hot Work Pre-solidified Steel has great toughness and high wear resistance. DB6 Steel is generally provided in hard, quenched, tempered and annealed condition in strengthened condition in exceptional cases. Normally it's working hardness is 360-430 BHN. This steel grade is the updated type of DIN 2713 for higher efficiency and performance.

Application:

Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Piston Rods, Bolster, Cranks, Cassettes, Plastic Moulds, Shearing Blades, Tools etc.

We are offering 2714 Die Block Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

Eaf+Lf+Vd+Upset+Forged+Annealed+Rough Turned For Rounds/Milled For Flats+Oil Quenched And Double Tempered+ Rough Turned For Rounds/Milled For Flats

Steel Properties:
The special Hot Work Pre-hardened Steel has great toughness and high wear resistance. DB6 Steel is generally supplied in hard, quenched, tempered and also in annealed condition in special cases. Usually it's working hardness is 360-430 BHN. This steel grade is the upgraded version of DIN 2713 for greater efficiency and performance.

Application:
Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Cassettes, Piston Rods, Cranks, Boaster, Shearing Blades, Tools, Plastic Moulds etc.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels supplies and stocks H13 tool steel in flat, square and round bar. We provide steel in all sizes as your requirements. Consult our team who will assist you for any query related to H13 steel.

SAE AISI H13 steel equivalent with JIS SKD61, GB 4Cr5MoSiV1 and DIN 1.2344 Tool Steel. AISI H13 steel consists of chromium, molybdenum and vanadium and is known for its high hardenability and great toughness.

The molybdenum and vanadium act as strengthening agents while the chromium content helps the AISI H-13 tool steel to withstand softening when used at high temperatures. It also combines shock and abrasion resistance, has good red hardness, can resist rapid cooling and withstand premature heat checking.

H13 Tool Steel has high hot-wear resistance abilities along with great strength, heat conductivity and invulnerability to hot cracking. It has good resistance to abrasion at each low and high temperature. It displays high level of toughness and ductility. H13 has Uniform and high level of machinability and polish ability. It has high-temperature strength and resistance to thermal fatigue, glorious through-hardening properties and shows very limited distortion during hardening.

H3 ESR is the most purified material with the conventional VD route. The nature of material increase the strength, exceptionally increase the micro-cleanness level. H13 ESR is most refined, has greater homogeneity and an exceptionally fine structure, resulting in improved machinability, polishing & high temperature tensile strength. Exceptionally suggest the use of AISI-H13 ESR grade for Aluminum Pressure Die Casting and other part subjected to high working temperatures and high weight quality. H13 is completely ultrasonic examined with 100% positive outcomes according to NDT standards.

Steel Properties:

• Great toughness

• Thermal conductivity

• High hot-wear resistance

• Hot tensile strength

• Insusceptible for hot cracking (Hot Crack resistant)

• Can be water-cooled to a restricted degree

• High Hardenability
  
  

Application:

This steel is especially used for ejector pins, tool holders and shrink work chucks. It is majorly widely utilized for manufacture of hot forging die & inserts, hot gripper dies, hot nut tools, hot header dies, brass forging and pressing dies, hot forging aluminum base dies, aluminum casting and extrusion dies, zinc die casting dies, extrusion mandrels, cores, die holder blocks, hot press dies, hot work punches, etc.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Stel Properties:

The exceptional Hot Work Pre-solidified Steel has great toughness and high wear resistance. DB6 Steel is generally provided in hard, quenched, tempered and annealed condition in strengthened condition in exceptional cases. Normally it's working hardness is 360-430 BHN. This steel grade is the updated type of DIN 2713 for higher efficiency and performance.

Application:

Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Piston Rods, Bolster, Cranks, Cassettes, Plastic Moulds, Shearing Blades, Tools etc.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

EAF+LF+VD+UPSET+FORGED+ANNEALED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS+OIL QUENCHED AND DOUBLE TEMPERED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS

Steel Properties:

The exceptional Hot Work Pre-solidified Steel has great toughness and high wear resistance. DB6 Steel is generally provided in hard, quenched, tempered and annealed condition in strengthened condition in exceptional cases. Normally it's working hardness is 360-430 BHN. This steel grade is the updated type of DIN 2713 for higher efficiency and performance.

Application:

Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Piston Rods, Bolster, Cranks, Cassettes, Plastic Moulds, Shearing Blades, Tools etc.

We are offering 2714 Tool Steel Block to our clients.

Chemical Composition - (Typical Analysis in %)

Ventura Alloy and Steels Stocks and Supplies Die Block Steels DB6 / 2714 in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe – a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm² & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).

Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.

Process Route:

EAF+LF+VD+UPSET+FORGED+ANNEALED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS+OIL QUENCHED AND DOUBLE TEMPERED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS

Steel Properties:

The exceptional Hot Work Pre-solidified Steel has great toughness and high wear resistance. DB6 Steel is generally provided in hard, quenched, tempered and annealed condition in strengthened condition in exceptional cases. Normally it's working hardness is 360-430 BHN. This steel grade is the updated type of DIN 2713 for higher efficiency and performance.

Application:

Dies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds, Shoe Blocks, Die Holder, Piston Rods, Bolster, Cranks, Cassettes, Plastic Moulds, Shearing Blades, Tools etc.